What makes a flip tape different from a standard tape
A standard tape measure usually has a single zero end and a hook or tip. You pull it out, read from that end, and retract it. A flip tape measure works from either end. The Dritz Quilters 120in Flip Tape Measure is built this way: the 1in mark is printed on each side at opposite ends, so you can measure from either end of the tape without hunting for the right starting point.
That difference matters most when you are taking repeated measurements across a quilt, measuring a long border, or working from both left and right sides of a project. Instead of flipping the tape around or walking back to the zero end, you simply use the nearest end. The tradeoff is that you need to pay attention to which scale you are reading, because the front and reverse sides carry different markings.
Flip tape vs standard tape: where each one fits
Both tools measure length, but they suit different habits and tasks. The comparison below focuses on what the supplied product information confirms about the Dritz flip tape, and on the general behavior of a standard tape measure.
- Reading from either end: The Dritz flip tape has a 1in mark printed on each side at opposite ends, so you can measure from either end. A standard tape typically has one zero end, so you must locate and hold that end for every measurement.
- Left- or right-handed use: The supplied description states the flip tape is equally efficient and comfortable for left-handed and right-handed users. A standard tape is not inherently handed, but its single zero end can feel awkward when you measure from the opposite side of a project.
- Marking layout: The Dritz flip tape has US customary markings in 1/16in increments on the front. The reverse has a split scale: US customary along the top edge and metric along the bottom. A standard tape may offer only one scale on one side, so check before you buy if you need both.
- Tape construction: The Dritz flip tape is non-stretch, reinforced fiberglass with steel tips on the ends. That construction is intended to resist stretching, which supports consistent measurements over time. A standard tape may be fiberglass, metal, or cloth; cloth tapes can stretch with use.
- Length and reach: The Dritz flip tape is 120 inches long, which suits long borders, backing, and repeated measurements across a quilt. A standard tape may be shorter or longer; match the length to the largest measurement you routinely take.
Dritz Quilters 120in Flip Tape Measure: the facts that affect accuracy
- Quilters 120in Flip Tape Measure #3011D: The 1in mark is printed on each side at opposite ends, allowing you to measure from either end of the tape. This is the core feature that separates a flip tape from a standard tape. It removes the need to find the zero end before every measurement, which reduces handling and repositioning on long quilt edges.

Quilters 120in Flip Tape Measure #3011D - Quilters 120in Flip Tape Measure #3011D: Non-stretch, reinforced fiberglass with steel tips on the ends. A tape that resists stretching is less likely to drift out of calibration with repeated use. Steel tips also give you a defined end point to reference.
- Quilters 120in Flip Tape Measure #3011D: US customary markings in 1/16in increments on the front; the reverse has a split scale with US customary along the top edge and metric along the bottom. You can read inches on either side, and metric on the reverse if your pattern uses it. The split scale means you should confirm which edge you are reading before you cut.
- Quilters 120in Flip Tape Measure #3011D: The tape is 120 inches long and is described as suitable for left-handed and right-handed users. Length covers most quilt borders and backing measurements, and the dual-end design means handedness does not force you to work from an awkward angle.
Where a flip tape helps and where a ruler still wins
A flip tape measure is a measuring tool, not a cutting guide. For short, straight cuts, a quilting ruler and rotary cutter remain the standard because the ruler gives you a rigid edge to cut against. A tape measure is flexible, so it follows curves and long spans but does not replace a ruler for squaring a block or trimming a seam.
The flip tape earns its place when you need to measure something longer than your ruler: the full width of a quilt, a border strip before you sew it on, or backing fabric. Its dual-end reading also helps when you measure from opposite sides of a large piece without walking around the table. If your work is mostly small blocks and precise trimming, a ruler is the more direct tool. If you frequently measure long distances and want to avoid hunting for the zero end, the flip tape is the more convenient one.
Practical checks before you choose
Use these checks to decide whether the Dritz flip tape belongs in your sewing kit alongside your rulers, or whether a standard tape is enough.
- Confirm the scale you need: The Dritz flip tape offers US customary on both sides and metric on the reverse bottom edge. If your patterns are metric only, check that the split scale layout works for how you read measurements.
- Check the length against your projects: 120 inches covers most quilt borders and backing measurements. If you routinely measure longer spans, confirm the length suits your largest project before relying on it.
- Decide whether dual-end reading saves you time: If you often measure from both ends of a quilt or work left-handed, the flip design removes a recurring annoyance. If you always measure from one end, a standard tape may be simpler.
- Keep a ruler for cutting: The flip tape measures; it does not provide a rigid cutting edge. Plan to keep a quilting ruler for trimming and squaring, and use the tape for long measurements.


